RC-Hangout

Re: Damon's Goblin KSE

2015-09-19T23:48:57

Flight videos have been uploaded , refer to http://www.rc-hangout.com/forum/viewtop ... 244#p20244 if you wish to watch them

Statistics: Posted by Kickedd7371 — Sat Sep 19, 2015 11:48 pm

Re: Damon's Goblin KSE

2015-09-20T00:54:25

Good catch! In tuning mode now myself.

Statistics: Posted by cml001 — Sat Sep 19, 2015 3:05 pm

Re: Damon's Goblin KSE

2015-09-19T12:24:15

Bet you are glad you caught the servo:)

Def!!! my second flight attempt when I thought the issue was esc settings related never got off the ground, literally. The motor would barely reach about 30% throttle and it would just cut out and wouldn't get past that point but yeah now she is all good!

Statistics: Posted by Kickedd7371 — Sat Sep 19, 2015 12:24 pm

Re: Damon's Goblin KSE

2015-09-19T12:22:03

Bet you are glad you caught the servo:)

Statistics: Posted by Graham Lawrie — Sat Sep 19, 2015 12:22 pm

Re: Damon's Goblin KSE

2015-09-19T12:19:53

So the maiden flight went well for the most part. She flew very nicely on the stock iKon settings with agility turned up to 90 and the cyclic gain turned down to 38. There was however an issue in regards to the motor cutting in and out during test flight. The issue was isolated to a faulty servo extension from the esc to fbl which has now been replaced. After the replacement I flew the heli another two times, on different sets of batteries (2 x 4000mah = 4 min flight time; comes down at storage charge, 2 x 5000mah = 5 min flight time; also coming down with a storage voltage). Flight number 2 and 3 will be uploaded in the next coming days and posted but all in all it has been a great day. This is def my favorite heli to fly !!!

Statistics: Posted by Kickedd7371 — Sat Sep 19, 2015 12:19 pm

Re: Damon's Goblin KSE

2015-09-18T13:33:09

Well the time has come she is all ready for a maiden flight tomorrow.

Statistics: Posted by Kickedd7371 — Fri Sep 18, 2015 1:33 pm

Re: Damon's Goblin KSE

2015-09-12T07:53:26

Nice parcels:)

Statistics: Posted by Graham Lawrie — Sat Sep 12, 2015 7:53 am

Re: Damon's Goblin KSE

2015-09-11T07:26:09

Score!

Statistics: Posted by cml001 — Fri Sep 11, 2015 7:26 am

Re: Damon's Goblin KSE

2015-09-11T05:23:14

And another small parcel has a arrived... Now I only need the 3 cyclic servos!

Statistics: Posted by Kickedd7371 — Fri Sep 11, 2015 5:23 am

Re: Damon's Goblin KSE

2015-09-11T05:18:10

I have ball end hex drivers I use on that one.

Cool, will see when i get up to that part.

Statistics: Posted by Kickedd7371 — Fri Sep 11, 2015 5:18 am

Re: Damon's Goblin KSE

2015-09-05T20:51:30

I have ball end hex drivers I use on that one.

Statistics: Posted by pvolcko — Sat Sep 05, 2015 8:51 pm

Re: Damon's Goblin KSE

2015-09-05T04:26:03

Big ass cooling mount. Might have trouble mounting those servos now, though.

haha yeah I noticed that, although shouldn't be too much of a headache; 3 out of the 4 screws I can get in with out any issues. The bottom right screw I will have to use a very short allen key wrench which I am pretty sure I have. Worst outcome is I have to remove the motor mount again haha which isn't too bad either.

Statistics: Posted by Kickedd7371 — Sat Sep 05, 2015 4:26 am

Re: Damon's Goblin KSE

2015-09-05T03:45:41

Big ass cooling mount. Might have trouble mounting those servos now, though.

Statistics: Posted by pvolcko — Sat Sep 05, 2015 3:45 am

Re: Damon's Goblin KSE

2015-09-04T16:56:30

Awesome... Get'n close!

Statistics: Posted by cml001 — Fri Sep 04, 2015 4:56 pm

Re: Damon's Goblin KSE

2015-09-04T11:30:14

Motor install done!

Statistics: Posted by Kickedd7371 — Fri Sep 04, 2015 11:30 am