Statistics: Posted by DOG — Mon Oct 05, 2015 2:16 am
]]>
]]>
Statistics: Posted by DOG — Mon Oct 05, 2015 1:09 am
]]>
First impression of the radio and fbl: Love em already. So setup is different than what I am used to but managed to get everything working as they should. First spool up was uneventful until I hit the throttle and it disappeared from the ground. For the radio it felt alright in my hands. Switches seem to work for me at this point. One down side is that there are to spring loaded switches. I think I can get rid of one of the springs and have a better option for throttle hold. I have the lower right shoulder switch as the main power cut and the right upper shoulder switch set to motor stop, motor idle and motor run.
Once I got the trim flight done I just moved the heli around in the air jut to get a better feeling for the setup. The gimbals were just as smooth as the servo travel, at that is how it looked. Response seemed damn near instant and felt connected. If there is any delay between stick input and heli reaction its very minimal. Today has some good sun light and with that the screen was very easy to see. What ever they did for that display it worked. As for everything else I would have to fly more before I can give and opinion. As of right now this is my new radio and dont think I will be looking anymore. I finally found that "Last" radio.
Statistics: Posted by murankar — Mon Oct 05, 2015 12:20 am
]]>
[*]Setup an account on Mikado's web site: http://shop.mikado-heli.de/
[*]Log into http://vstabi.info with your new Mikado id and leave the browser open. You will need an active session for this to work.
[*]Download the VControl Center and install it like any other app and follow the instructions as the appear
[*][*]Once its done installing you will have the vstabi tuning software and the control center
[*][*]You may have to go to device manager and update the drivers for both the radio and/or Neo. You should already know how to do
[*][*]do this. If not let us know.
[*]Plug in either the Vcontrol or the Neo and launch the control center. at this point it is going to update what ever you plugged in.
[*]After the updates are done you will need to click the applications button on the top right side of the window. This should open a new tab in your browser showing you a list of registered products. At this point everything should be registered. DO NOT try and register straight through vstabi.info, it wont work for the NEO.
If you want to use vstabi to help in setting up your new Neo you will need to down load your keys file which is linked right under your Neo info. Once downloaded you will need to move it to your vcontrol root file under program files x86 (i believe). Once you open the vcontrol file past or move it to there. When you launch the vstabi software it should read the keys file. Now you should be able to use your usb cable and plug in to set it up.
I found that leveling the swash was easier in vstabi than the radio. I have not figured out how to adjust individual servos in the vcontrol just groups. Since I follow the Soko method for setting up it was easier for me that way. Now supposedly the free swash app for the vcontrol gives you that option but have not figured out how to do it. Right now the Gaui is waiting for the trim flight witch should be right after I wake up.
Now for the infamous throttle and pitch curves, good luck finding them. They don't exist in the radio at all. SO for castle its not that tough to setup since we are dealing with an external governor. On the Motor screen (BTW you will need the castle link to do this) uncheck auto bail out, set it to external governor and for the sensor wire (the white one) set it to rpm sensor and plug it into the Neo sensor port in the back of the unit (near the antenna wires). In the radio you will need to set the percentages of throttle and what head speeds you want along with the magnet count divided by 2 along with your gear ration. My gear ratio is higher than the max for the Neo, So I need to consider an 11T pinion at the minimum. FOr now I will stick with the 10T and see what happens. When selecting your esc in the radio it gives you an option to choose an ESC I chose Castle for obvious reasons. When I did that I got a QR code that I scanned with my phone and the stup page came up in chrome on my phone. Followed that and got it to work. Pitch curves are all linear not matter what.
Now in order to use the radio you will need to know where throttle hold is along with the safety switch. The safety switch renders the model useless except servos. I believe the safety switch is used for throttle hold while the throttle cut is a three way switch that gives you motor on, motor idel and motor off.
Bank switching is going to be NEEDED thats it no choice really. So what does this mean, you can have up to three different setups for the same heli based on which bank your on to include your governor. So with that said I set my banks to be the same on agility and style while setting head gain with three different values at 10 points apart, lowest number for higher head speed and and highest for lower head speed. Thats it everyhting else is the same in all banks. Now for the fun part, set your 2 knobs to a tune setting, go fly and while your flying adjust the knobs as need to tune out any issues and that should get you really close to a good tune. All that's left is fine tuning if you feel you need it. Most of us wont but for the 5% who do then keep going to your content with the tune. Last thing the knobs can be your worst nightmare. On some things the knobs are relitive and on others they are absolute. You will need to RTFM to figure that out. I did RTFM and that's how I found that info out. just do some reading first.
FOr now that all I have on the radio. I will be diggin in more as time goes on and I start fly again.
Statistics: Posted by murankar — Tue Sep 29, 2015 8:36 am
]]>
Glad you got things figured out on registering things.
Statistics: Posted by pvolcko — Tue Sep 29, 2015 5:09 am
]]>
]]>
You should PM Cameron if you have any issues:) He would be more than happy to help:)
Statistics: Posted by Graham Lawrie — Sat Sep 26, 2015 10:38 am
]]>
So after looking at the main setup stuff (which still needs done) I went and looked for the throttle curves and pitch curves. After almost 30 minutes of looking for it I had to google it. Apparently Vcontrol does not use these. Thats why it is heavily governor dependent. So if you dont know governors and want this radio you will need to learn it.
The break down of the radio is as follows: 6 thee way switches with two being sping loaded in the full up position (lower two shoulder switches). 2 knobs and zero trim buttons. Yes no trim, why because the vbar will auto trim while in flight if you chose that mode; plus you dont need them with fbl units. The radios screen is not in color but it is ver well lit and slightly odd to look at. Its not the same as a normal lcd screen it has very high contrast with out adjusting the contrast. The sticks are soooooooooooooo smooth compared to the DX6. While the DX6 does have smooth sticks the vcontrol is more smooth.
Now that the Gaui is almost done i think I should be flying by the end of the weekend. One thing to remember is that this radio (at this time) may not work with real flight 7 unless you spen at least $110 USD for the make shift adapter Mikado came up with to solve this issue. The radio will plug in as a usb controller. So if your sim can do usb controllers then it SHOULD work. One suggestion I found is not to mess with the radio for the sim, use the in sim set up to run it with the sim. Mikado says that you could mess with the model setup if you use the radio for setup.
Last thing: Your Vcontrol will automatically set the model in the radio based on the NEO or Vbar plugged in. SO no more changing models, I like this because the day I get my Mikado 550 SX (or is it SE).
As I go on with this I will add more info.
Statistics: Posted by murankar — Sat Sep 26, 2015 6:05 am
]]>
]]>
]]>
Issue 2: went to register the neo and the serial number is invalid.
Statistics: Posted by murankar — Wed Sep 23, 2015 7:54 am
]]>
Statistics: Posted by murankar — Wed Sep 23, 2015 6:12 am
]]>
]]>
Lot of new stuff to learn and fiddle with.
That's what I am most excited about. Taking the time to learn something new. The other part is no more laptop or cell phone to tune. It's all at your finger tips. I might do a wrap on it.Statistics: Posted by murankar — Tue Sep 22, 2015 7:24 am
]]>