Dans HPI trophy 3.5

You drive it, you document it. Story of the day's activities. As always, video is better!

Moderator: Moderators

Forum rules
Members are encouraged to start and keep a single thread for all their RC driving exploits. Alternatively you may start a thread per vehicle. If you wish to post a one-off thread about a particular event you can, but please link to it in your normal thread, and vice versa.
Post Reply
User avatar
danhampson
Site Admin
Site Admin
Posts: 1746
Joined: Thu Nov 06, 2014 2:54 pm
Location: Manchester, United Kingdom
Contact:

Dans HPI trophy 3.5

Post by danhampson »

I've gone a purchased a nitro off road buggy.
I saw it a a great price as it was the display model and thought it would be something that I can do with the kids this summer. I've secretly fancied a go at nitro for a while.
20160416_140917.jpg
20160416_140917.jpg (3.57 MiB) Viewed 3890 times
20160419_181353.jpg
20160419_181353.jpg (2.42 MiB) Viewed 3890 times
20160419_181427.jpg
20160419_181427.jpg (2.57 MiB) Viewed 3890 times
So far I have run the engine in.

I did this by running it at idle for 2 tanks with the wheels off the ground. Then 1 tank doing figure 8's blipping the throttle to 1/4, 1 tank same as but 1/2 throttle and a last tank at 3/4 throttle with a few full throttle blips here and there. It seems to be running sweet.

I'm hoping to get out tomorrow for some tuning. I'll charge the camera and shoot some video if I get out
FPV addict.
User avatar
Lee
Moderator
Moderator
Posts: 1824
Joined: Fri Nov 07, 2014 6:16 pm
Location: Tarifa, Spain

Re: Dans HPI trophy 3.5

Post by Lee »

Sweet Dan.
My friend has an HPI 1/5 scale Baja Gasser.
Great fun, but need more cars to race with.
GOBLIN 570------IKON
WARP 360--------IKON
QAV 500----------Open Pilot
RCXH250---------Open Pilot


Citizen #229
User avatar
Derek
Supporter
Supporter
Posts: 3948
Joined: Fri Nov 07, 2014 7:45 pm
Location: Fort Wayne, Indiana, USA

Re: Dans HPI trophy 3.5

Post by Derek »

lol....Dan is beginning to get his hands into everything now, lol.

That's a sweet looking buggy, Dan! Very cool!
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8

Citizen # 00744
User avatar
Graham Lawrie
Moderator
Moderator
Posts: 5049
Joined: Thu Nov 06, 2014 7:14 pm
Location: Kinlochleven, Scotland
Contact:

Re: Dans HPI trophy 3.5

Post by Graham Lawrie »

Very nice Dan:)
Align 600
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius




CITIZEN # 521
User avatar
danhampson
Site Admin
Site Admin
Posts: 1746
Joined: Thu Nov 06, 2014 2:54 pm
Location: Manchester, United Kingdom
Contact:

Re: Dans HPI trophy 3.5

Post by danhampson »

Lee wrote:Sweet Dan.
My friend has an HPI 1/5 scale Baja Gasser.
Great fun, but need more cars to race with.
There a very nice model but out of my price range atm.
Derek wrote:lol....Dan is beginning to get his hands into everything now, lol.

That's a sweet looking buggy, Dan! Very cool!
You know me Derek I like a challenge and love learning new stuff.
Graham Lawrie wrote:Very nice Dan:)
Thanks Graham, I've got some friends who have got 1/8th scale off road nitro's there's about 6 of us with them now so we are going to set some racing up in the summer.
FPV addict.
User avatar
danhampson
Site Admin
Site Admin
Posts: 1746
Joined: Thu Nov 06, 2014 2:54 pm
Location: Manchester, United Kingdom
Contact:

Re: Dans HPI trophy 3.5

Post by danhampson »

I had the trophy out again over the weekend and have started to get my head around the nitro tuning it took me about a tank to get it tuned, and this thing is fast.

The only downside to this model is the pull start, after Saturdays session I had some lovely blisters between my fingers which isn't good as the environment I work in has a very high salt content (ouch!!). To remedy this I've ordered a 12v starter box, this starter box is supposed to be powered by a small 12v motorbike battery. But I'm going to power if from a couple of 3s lipos in parallel. It also has an 1.4v output for a wired glow starter, which I've purchased with the box.

I've got some video to post of the car in action but iv not had chance to upload it yet, I'm hoping to do that in the next day or so.
FPV addict.
User avatar
Derek
Supporter
Supporter
Posts: 3948
Joined: Fri Nov 07, 2014 7:45 pm
Location: Fort Wayne, Indiana, USA

Re: Dans HPI trophy 3.5

Post by Derek »

That sucks about the blisters but it's cool that you got the car out for some play. I'd like to have something like that.
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8

Citizen # 00744
User avatar
danhampson
Site Admin
Site Admin
Posts: 1746
Joined: Thu Nov 06, 2014 2:54 pm
Location: Manchester, United Kingdom
Contact:

Re: Dans HPI trophy 3.5

Post by danhampson »

Derek wrote:That sucks about the blisters but it's cool that you got the car out for some play. I'd like to have something like that.
It's great fun Derek the smell the sound I think I'm in love with nitro.

I went to a local hobby shop today and picked up an upgrade clutch kit and the the tools to change it.
20160429_183910.jpg
20160429_183910.jpg (1.4 MiB) Viewed 3860 times
FPV addict.
User avatar
danhampson
Site Admin
Site Admin
Posts: 1746
Joined: Thu Nov 06, 2014 2:54 pm
Location: Manchester, United Kingdom
Contact:

Re: Dans HPI trophy 3.5

Post by danhampson »

I replaced the clutch and fly wheel last night. It didn't really take that long.
20160429_193243.jpg
20160429_193243.jpg (1.31 MiB) Viewed 3852 times
20160429_193612.jpg
20160429_193612.jpg (1.12 MiB) Viewed 3852 times
The new clutch pads came with 3 different strength springs, I opted for the silver (medium) ones.
20160429_194621.jpg
20160429_194621.jpg (1.96 MiB) Viewed 3852 times
20160429_195759.jpg
20160429_195759.jpg (962.2 KiB) Viewed 3852 times
I had to nip out at this point and forgot to take any more pictures of the process. After the last image I removed the bearings from the clutch bell and washed the clutch shoes flywheel and bell in clutch and brake cleaner before replacing the cluch bell over the shoes and re-fitted the engine.
I'm just waiting for the weather now to have a test run.
FPV addict.
User avatar
Graham Lawrie
Moderator
Moderator
Posts: 5049
Joined: Thu Nov 06, 2014 7:14 pm
Location: Kinlochleven, Scotland
Contact:

Re: Dans HPI trophy 3.5

Post by Graham Lawrie »

Looks really nice Dan:)
Align 600
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius




CITIZEN # 521
Post Reply

Return to “Member Logs”