Krieger 200.

[danhampson]

My new frame arrived yesterday from Germany.
This will not be a full build thread as I'm going to recycle a lot of the parts that are on the temp zmr frame and save the new parts for my little secret. So here are a few shots of the frame.

20151013_133110.jpg (3.24 MiB) Viewed 2682 times

2015-10-13 14.07.07.jpg (1.55 MiB) Viewed 2682 times

20151013_140610.jpg (2.95 MiB) Viewed 2682 times

20151013_140620.jpg (3.33 MiB) Viewed 2682 times

[attachment=0]20151013_140640.jpg[/attachment


This was just a dry fit to see how the frame, it's a bit fidley to assemble but is rock solid when screwed together

[KevG]

Looks so frigging simple Dan, nice butt,

[danhampson]

I can't belive how little space there is for the electronics. This is going to be a challenging build I think I may have to desolder the headers off my re and hard wire it all.

[Derek]

It's an interesting frame....no doubt!

[Graham Lawrie]

It looks great Dan but small:) hard wire everything i think:)

[danhampson]

Made a start on the build last night.

Headers desoldered, wires and jumpers hard wired to the receiver

20151016_185608.jpg (3.05 MiB) Viewed 2655 times

Receiver given a sexy new rubber suit and installed in the frame.

20151016_202945.jpg (3.34 MiB) Viewed 2655 times

Started to solder pcb with 12v and 5v regulators

20151016_203023.jpg (3.71 MiB) Viewed 2655 times

For the end of play I've got the pcb fully wired up ready to install the naze32

[Graham Lawrie]

Looking good Dan:) space does look tight:) Hard wired seems to be the way builds are going to cut down on weight

[danhampson]

Finally got the build finished.

Installed naze32, everything hard wired.

20151017_182954.jpg (3.66 MiB) Viewed 2632 times

Ready for maiden.

20151018_204937.jpg (3.15 MiB) Viewed 2632 times

[danhampson]

I did run into a snag with the build, the regulators on the pdb are rubbish. Every time the motors started to spin the regulators went off and back on causing the naze32 and esc's to reboot. So i bypassed the regulators and added a trusty old hobbywing bec, wire that to the naze and fpv cam and wired the vtx directly to the battery input.


Jobs a good un....


Thought I had better weigh it for you guys. This is with a 4s 1300mah pack ready for take off (if the wind ever drops)

20151022_063248.jpg (3.24 MiB) Viewed 2627 times

Maiden is going to be flown with 20 degrees on the fpv cam to start with to see how the hd footage turns out as the yi camera has 45 degrees on it, so I may need to run 30 degrees on the ccd, which should make for some really fast flights.

This thing scares the crap out of me

[DOG]

Hey danhampson. That's a tiny craft you got their. It reminds me of one the drones/spaceship on a movie called " Batteries not Included " by Steven Spielberg. Got luck on your madien and video please.

[KevG]

Let's hope Mother Nature plays fair with you then mate, good luck on the maiden,

[danhampson]

Thanks guys. Looks like it could be a after work maiden, weather forecast is good for morning

[danhampson]

Walking back from the rugby pitch, Blown away.

Video to follow....

[KevG]

Blown away good or blown away windy?

[cml001]

Neat looking!

[danhampson]

Blown away good or blown away windy?

Blown away, good.

Neat looking!

I think it looks a bit wierd but flight performance more than make up for its strange look

check out the maiden http://rc-hangout.com/forum/viewtopic.php?f=96&t=1449