RCX(ZMR)250 (RE)Build

Got a new project going on? Document your builds of aircraft here. Video and pictures highly encouraged!

Moderator: Moderators

Forum rules
Please post one thread per aircraft or project. If you're doing a rebuild or major make over of an existing aircraft you can start a new thread, but you are encouraged to cross link the new thread and original build thread so people can easily see the history of your aircraft.
Post Reply
User avatar
Stambo
Member
Member
Posts: 1349
Joined: Thu Nov 20, 2014 7:13 pm
Location: Whangarei New Zealand

RCX(ZMR)250 (RE)Build

Post by Stambo »

Woohoo, my batteries finally arrived.
Time to rebuild my quad. :)
Photo0731.jpg
Photo0731.jpg (531.55 KiB) Viewed 1696 times
New 4s batteries.
New Naze32, will run Cleanflight initially then maybe switch to Betaflight and see what it is like.
New D4R2
New Sunnysky 2207 2100kv
New Kiss ESCs I will flash them to the latest BLHeli firmware
Photo0732.jpg
Photo0732.jpg (524.81 KiB) Viewed 1696 times
The only original parts will be my video system and my old frame.
Although I may switch back to the Fatshark 250mw vtx.
Photo0733.jpg
Photo0733.jpg (518.85 KiB) Viewed 1696 times
All the old parts will probably end up on another frame for Jacob at some stage. :)
RCX 250 Minquad FPV addiction
500 X quad FPV/AP platform
450 X quad set up for night flight
Multiple WLToys V911, V949, V959
Taranis, Turnigy 9X
Fatshark Predator, Immersion 5800 Duo
Trex 500 Esky Belt CP V2
User avatar
Stambo
Member
Member
Posts: 1349
Joined: Thu Nov 20, 2014 7:13 pm
Location: Whangarei New Zealand

Re: RCX(ZMR)250 (RE)Build

Post by Stambo »

Wow, this thing is filthy inside, time for a clean before rebuilding it.
Photo0734.jpg
Photo0734.jpg (431.73 KiB) Viewed 1692 times
RCX 250 Minquad FPV addiction
500 X quad FPV/AP platform
450 X quad set up for night flight
Multiple WLToys V911, V949, V959
Taranis, Turnigy 9X
Fatshark Predator, Immersion 5800 Duo
Trex 500 Esky Belt CP V2
User avatar
KevG
Supporter
Supporter
Posts: 1642
Joined: Fri Nov 07, 2014 4:59 pm
Location: South Wales, UK

Re: RCX(ZMR)250 (RE)Build

Post by KevG »

Stambo make sure you don't put to much heat into the kiss esc's when soldering, this has been said to help with magic smoke,

Nice haul mate,
Minor league Aviator, against gravity which normally wins!

RotoriousFPV quads Micro Rad 3" Gat 4" and Rad 5"
D-Quad Obsession
Yuneec Typhoon H
Taranis Qx7,
User avatar
danhampson
Site Admin
Site Admin
Posts: 1746
Joined: Thu Nov 06, 2014 2:54 pm
Location: Manchester, United Kingdom
Contact:

Re: RCX(ZMR)250 (RE)Build

Post by danhampson »

Looks like you've got some nice pieces there Stambo.
What's the bec your using for the rebuild?
FPV addict.
User avatar
Stambo
Member
Member
Posts: 1349
Joined: Thu Nov 20, 2014 7:13 pm
Location: Whangarei New Zealand

Re: RCX(ZMR)250 (RE)Build

Post by Stambo »

danhampson wrote:Looks like you've got some nice pieces there Stambo.
What's the bec your using for the rebuild?
It's a little 3amp mini ubec from the guys I got the Kiss ESCs from.
Hopefully it will be enough to run the FC and RX and keep the Mobius charged.
The video TX and cam are both capable of running 4s but I will eventually need a 12v bec or a little regulator for some LEDs.
RCX 250 Minquad FPV addiction
500 X quad FPV/AP platform
450 X quad set up for night flight
Multiple WLToys V911, V949, V959
Taranis, Turnigy 9X
Fatshark Predator, Immersion 5800 Duo
Trex 500 Esky Belt CP V2
User avatar
Stambo
Member
Member
Posts: 1349
Joined: Thu Nov 20, 2014 7:13 pm
Location: Whangarei New Zealand

Re: RCX(ZMR)250 (RE)Build

Post by Stambo »

I was wondering what to do for power distribution when I spied a faulty PC power supply.
I took it apart and found a bit of circuit board with some nice wide tracks on it.
Out with the Dremel and cut it to size.
Sanded the tracks a little and flowed solder over the whole things, good enough for me. :)
Sorry about the poor quality pics, camera battery was flat and had to use my phone.
Photo0736.jpg
Photo0736.jpg (367.46 KiB) Viewed 1679 times
Motors and ESCs on , arms attached and distribution board hooked up.
Photo0739.jpg
Photo0739.jpg (634.99 KiB) Viewed 1679 times
Photo0740.jpg
Photo0740.jpg (305.66 KiB) Viewed 1679 times
Next day, all assembled, Naze32 and ESCs all set up, ready for some testing.
Maiden video to come, good, bad or otherwise. :)
Photo0741.jpg
Photo0741.jpg (461.75 KiB) Viewed 1679 times
RCX 250 Minquad FPV addiction
500 X quad FPV/AP platform
450 X quad set up for night flight
Multiple WLToys V911, V949, V959
Taranis, Turnigy 9X
Fatshark Predator, Immersion 5800 Duo
Trex 500 Esky Belt CP V2
User avatar
Stambo
Member
Member
Posts: 1349
Joined: Thu Nov 20, 2014 7:13 pm
Location: Whangarei New Zealand

Re: RCX(ZMR)250 (RE)Build

Post by Stambo »

Did the remaiden, it did not go completely to plan but I am puzzled as to what happened.
First hover, about 2 feet off the ground in self level, gave it a few flicks to test reactions and it just fell out of the sky.
I have no idea why, I checked motor and ESC temps, one motor was warm, the rest were cold.
I checked all my connections and tried again, acro this time with no issues.
I put in a new battery and put on the goggles.
I also very quickly put a huge smile on my face.
This thing is fast, real fast.
Took it reasonably easy the first couple of flights then just went for it.
Checked the motor and ESC temps after each flight and they were stone cold.
Running DAL 5045 bullnose at the moment but just for interest sake I am gonna try some 6040.
I will probably lose a bit of handling but I need to know how much faster it goes. :)
I will upload some videos when I finish editing them. :)
Been a little busy on my patch of dirt. :)
RCX 250 Minquad FPV addiction
500 X quad FPV/AP platform
450 X quad set up for night flight
Multiple WLToys V911, V949, V959
Taranis, Turnigy 9X
Fatshark Predator, Immersion 5800 Duo
Trex 500 Esky Belt CP V2
User avatar
Stambo
Member
Member
Posts: 1349
Joined: Thu Nov 20, 2014 7:13 pm
Location: Whangarei New Zealand

Re: RCX(ZMR)250 (RE)Build

Post by Stambo »

Finally edited my re maiden video.

https://www.youtube.com/watch?v=00-lZLOTrqg

First FPV flights to come.
RCX 250 Minquad FPV addiction
500 X quad FPV/AP platform
450 X quad set up for night flight
Multiple WLToys V911, V949, V959
Taranis, Turnigy 9X
Fatshark Predator, Immersion 5800 Duo
Trex 500 Esky Belt CP V2
User avatar
Graham Lawrie
Moderator
Moderator
Posts: 5049
Joined: Thu Nov 06, 2014 7:14 pm
Location: Kinlochleven, Scotland
Contact:

Re: RCX(ZMR)250 (RE)Build

Post by Graham Lawrie »

Nice one Stambo:) i killed my esc,s at the weekend too much heat resoldering:)
Align 600
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius




CITIZEN # 521
Post Reply

Return to “Member Builds”