Page 1 of 1

PDB went bad?

Posted: Wed Dec 06, 2017 9:09 am
by DOG
Hey there. I'm not a happy camper :evil: I've been waiting for awhile now to get my Shuriken 180 flying. Finally I got new esc and motors from HobbyKing USA and they arrived yesterday. I just finished installing them and had it hooked up to clean flight. I wanted to make sure my receiver tab, modes and everything else was working properly. So as soon I plugged the battery in and POOF the magic smoke came out of one of the motors :(. Being new ESC and motors installed, can the PDB be bad? How can I test the PDB to see if that's the problem.

Re: PDB went bad?

Posted: Wed Dec 06, 2017 7:52 pm
by Graham Lawrie

Re: PDB went bad?

Posted: Wed Dec 06, 2017 10:47 pm
by Stambo
Make yourself one of these, might save some pain in the wallet.
Once the smoke gets out it's hard to prove who's fault it is, better to stop it from happening in the first place.

https://www.youtube.com/watch?v=4z7yRG56aKM

Re: PDB went bad?

Posted: Thu Dec 07, 2017 12:19 am
by DOG
Wow Stambo. I thank you very much for that video. I wish I knew that sooner. I would of save a few motors and esc by now. Too cool and i'm in the process of making one :D

Re: PDB went bad?

Posted: Thu Dec 07, 2017 1:43 am
by Stambo
No worries Dog.
I always use one on my first hookup, it has saved me more than once. :D

Re: PDB went bad?

Posted: Thu Dec 07, 2017 2:19 am
by Derek
I've never used one of those Smoke Stoppers. Stambo, you said that you always use one on your first hookup. If the wiring is all correct, does the light come on or does it come on when the wiring is incorrect. What happens when the wiring is correct and what happens when the wiring is incorrect?

Re: PDB went bad?

Posted: Thu Dec 07, 2017 3:37 am
by Stambo
Light comes on when something is shorted, saved me from smoking an ESC a while back, I had soldered the wires around the wrong way on it.
It may glow very dim when you hook up, more likely not at all, depends what you have connected, if it is bright, it just saved you some money. :D

Re: PDB went bad?

Posted: Thu Dec 07, 2017 4:02 am
by Derek
That's interesting. So....the light comes on if something is wrong. the light doesn't come on if everything is good.

Re: PDB went bad?

Posted: Thu Dec 07, 2017 7:37 pm
by Stambo
Derek wrote:That's interesting. So....the light comes on if something is wrong. the light doesn't come on if everything is good.
Pretty much it, don't try to run the motor with it on there though.
It's only for initial hookup.

Re: PDB went bad?

Posted: Thu Dec 07, 2017 8:34 pm
by DOG
Well, sure enough it's the board. I had the same problem with the same exact side of the board. That's why I ended up getting new motors and esc. I guess the 180 is no good since the PDB is part of the frame. Derek mention awhile back if something goes wrong with the PDB on this quad, it can't be fixed. I should be able to use the frame. All I have to do is install a new FC, new motors and ESC and a VTX. I can make room for the FC. The ESC and motors are already there and put the VTX in. Is this possible?

Re: PDB went bad?

Posted: Fri Dec 08, 2017 7:59 am
by DOG
The PDB didn't go bad... it was owner mistake :oops: Small amount of solder was touching where it wasn't suppose too :o I clean it up and now I have my 180 back :D

Re: PDB went bad?

Posted: Fri Dec 08, 2017 8:48 am
by Derek
It's amazing how just a bit of solder can fouls things up. Do you remember when you couldn't get your 180 to work when you first got it? You ended up shipping it to me and I found a bit of solder on the boot jumpers and that was why it wouldn't load up. Glad we got that sorted!