My PID Settings:)

Graham Lawrie · Post by **Graham Lawrie** » Sat Mar 28, 2015 11:17 am

Latest settings. Comments please:)

Graham Lawrie · Post by **Graham Lawrie** » Sat Mar 28, 2015 11:21 am

And. More:)

Graham Lawrie · Post by **Graham Lawrie** » Sat Mar 28, 2015 12:54 pm

Weather now bad:( settings now that seem not too bad, but the acro mode is super fast do I increase RC EXPO it is at 60?

Post by **danhampson** » Sat Mar 28, 2015 1:30 pm

Are these pids with the afro esc's?
Decrease the roll and pitch rate that will slow it down in rate mode I don't know how that will affect any of the other modes.

Graham Lawrie · Post by **Graham Lawrie** » Sat Mar 28, 2015 4:10 pm

Yes Dan the last one is where i am at and it is with the Afro esc,s:)

Stambo · Post by **Stambo** » Sat Mar 28, 2015 10:00 pm

Drop your RC rate, 1.5 is way high, I run about 1.2 if I wanna go nuts or less than 1 if I am taking it easy.

And for taking pictures of your screen, windows has a thing called "Snipping Tool" gives much clearer images and it is already in your computer.

Start typing it in the start menu and it will come up.

Graham Lawrie · Post by **Graham Lawrie** » Sat Mar 28, 2015 10:38 pm

Double thanks Stambo:)

Stambo · Post by **Stambo** » Sat Mar 28, 2015 11:09 pm

I see your roll/pitch rate is quite high too, I run mine about 0.40

Here is my current settings.
You can set up different profiles then select them when you fly by holding the left stick in the disarm position and using the right stick to choose profile.
Right stick left = profile 1
Up = profile 2
Right = profile 3
Down will recalibrate acc, don't do it unless the quad is dead level.

FC will beep and LED flash to indicate the selected profile.
Whatever you have selected when you exit the configurator will be what the quad starts with so if you want to fly profile 1 make sure it is selected.

: PID P1.JPG (54.52 KiB) Viewed 2450 times

: PID P2.JPG (52.46 KiB) Viewed 2450 times

: PID P3.JPG (52.67 KiB) Viewed 2450 times

Graham Lawrie · Post by **Graham Lawrie** » Sun Mar 29, 2015 12:49 am

Cheers Stambo:) what are the 3 profiles eg 1= easy 2= acro fast etc etc........

Stambo · Post by **Stambo** » Sun Mar 29, 2015 3:36 am

Graham Lawrie wrote:Cheers Stambo:) what are the 3 profiles eg 1= easy 2= acro fast etc etc........

Just experimenting with different settings to see what works best.

Graham Lawrie · Post by **Graham Lawrie** » Sun Mar 29, 2015 10:13 am

Flew in my back garden on your Profile 1 and they are the best settings i have tried:) Very stable in angle and same in acro. Many thanks again Stambo:)

Derek, you should give Stambos settings a go:)

Post by **danhampson** » Sun Mar 29, 2015 1:17 pm

You should be able to run you pitch and roll P gains much higher than that with oneshot enabled graham.
have you enabled oneshot in the configuration tab in clean flight?

Graham Lawrie · Post by **Graham Lawrie** » Sun Mar 29, 2015 4:46 pm

No Dan:) not looked at oneshot yet?

Post by **danhampson** » Sun Mar 29, 2015 7:06 pm

If you are going to start tuning you would be better off turning oneshot on in the naze software, it saves tuning once then turning it on and having too do it all again. Plus ive found thet with oneshot on its a lot easier to tune as if the sweet spot is bigger/easier to find

Graham Lawrie · Post by **Graham Lawrie** » Sun Mar 29, 2015 7:25 pm

Interesting Dan:) i will need to look into it and see whay it is:) Apaart from knowing it is a CLI command i dont know anything about it?

Post by **danhampson** » Sun Mar 29, 2015 7:45 pm

It's a check box in the in the configuration tab under the motor stop check box. And the set looptime = 1600 in the cli and your good to go, your flashed esc's will sense oneshot and switch to that mode.

Tony · Post by **Tony** » Sun Mar 29, 2015 9:12 pm

Wish I had cleanflight so I could follow this thread, very interesting...

Graham Lawrie · Post by **Graham Lawrie** » Sun Mar 29, 2015 9:28 pm

danhampson wrote:It's a check box in the in the configuration tab under the motor stop check box. And the set looptime = 1600 in the cli and your good to go, your flashed esc's will sense oneshot and switch to that mode.

Will it alter Stambos settings for profiles 1,2,3 that i have put in?

Stambo · Post by **Stambo** » Sun Mar 29, 2015 11:31 pm

I don't have any oneshot capable ESCs so I don't know what difference it will make but I have read oneshot makes tuning easier.
You should be fine, and as Dan says, you should be able to up the P some more.

RC-Hangout

My PID Settings:)

My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)

Re: My PID Settings:)