Forum rules
Members are encouraged to keep either a single thread for all their flying activities or post a thread per aircraft. If you want to make a one-off thread about a particular flight/event go ahead, but please put a link to that thread in your normal flight thread and vice versa.
Tony wrote:Really cool flight too, pleased THERES no damage... Have you made any spares for it Dan?
the spares i have are a few clamps and a length of carbon tube
Stambo wrote:Looking much smoother Dan.
Looks like it's time to tilt that cam up a bit more, or rotate the arms a bit.
Im going to tilt the motors by 10° once im a bit happier with the pids.
I think ive found the problem with the GPS, i forgot to turn the mobius on for one of my flights this morning and what happens, the gps starts working.
After a few hour research last night, the conclusion is that the Mobius generates enough rf interference to affect the gps sat lock. I've tested the mobius with the gps on the quad, phone and tablet and the results are the same for all the devices.
With the mobius off all devices get full 3d lock, it's the same with the mobius on standby. As soon as the mobius is recording all the tested devices loose gps signal.
to try to combat this I have covered the abs gps mount with aluminum tape and move the mount to the rear of the frame.
Static testing has gone well so far this morning full gps lock was held when the mobius was recording on the ground. Going to the field soon for some more testing and pid tuning
lmao.....that is wicked fast!!! I loved that! Ha ha ha!
It's a shame that my new 290 quad turned out so heavy (at least I think it's heavy). I need to weigh it. I've got an extra set of motors, new 20amp Afro's, an extra Naze32 board, an extra breakout cable, and a bunch of props. I'm gonna try to draw up a smaller and much lighter new quad, lmao. Just need to order some new carbon fiber.
Great flying Dan! I love that machine!!!
What OSD are you using?
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
That's awesome Dan, nice one mate...I see what you meant with the OSD clutering the screen though, but looks good..
Tony - AKA Blackwarrior - nice to be home again
Novice pilot HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
Ive just ordered a new flip32+ and ive found a cable that i can use to rewire the vtx (it might work it might not). it looks like the cause was the OSD moving and the pins on the analog side made contact with the frame, i will have to check if the OSD is working too.
The weather report for tomorrow isn't good, so i may start the tear down in the morning.
Minimosd board fried, lucky for me ive got a spare board, mavlink osd (known working). The wiring for the VTX also fried and of course the flip32 it looks like ive knocked the osd and the skicky pad insulating the osd came off
20150617_115415[1].jpg (1.59 MiB) Viewed 2393 times
so far ive reloomed the vtx, installed the mavlink osd and tested the video up link using a broken flip32 everything is working fine so its the usual waiting game for the new flip32+
Wicked power there Dan.
Did you see Malc from RCTVUK?
He tried 6S on his. Gave it some stick, and all the props sheared off
I think carbon props are a must on something with that much pop.
GOBLIN 570------IKON WARP 360--------IKON QAV 500----------Open Pilot RCXH250---------Open Pilot
the props im flying at the moment are cut down HQ 8x4.5 ABS and ive also got some HQ 7x4.5 carbon composite. And ive just had a moment of madness and ordered a set of HQ 10x6 carbon composite tri blades to cut down.
My new flip32+ arrived today, flashed it, restored to last backup and installed on the quad. And ive found another casualty from the crash, motor 3 has lightly smoked windings and doesnt spin up, alll the other motors spin up fine. ive ordered a replacement that should be here in about a week
You've had a massive learning curve there Dan with all these quad builds and flights, must say your knowledge is immense. Keep it coming mate, we are all learning from it...
Tony - AKA Blackwarrior - nice to be home again
Novice pilot HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
The learning curve has been quite steep with this build due to addition of the osd and gps mainly but it's been great fun and it has got me thinking about doing another scratch build maybe something a bit bigger.
Tony - AKA Blackwarrior - nice to be home again
Novice pilot HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
Tony wrote:Yeah, maybe something you can sit in Dan....lol
Don't tempt me Tony.
Well I think you should Dan, be cool
Tony - AKA Blackwarrior - nice to be home again
Novice pilot HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
