Emax nighthawk 250 build thread

KevG · Post by **KevG** » Fri Jan 30, 2015 9:28 am

I think it was in attitude, attitude, axis lock in the flight mode, but set up on generic luminier 250 values, was getting late last night so did not look around to much,

wish there was a good guide around for this controller,

Tony · Post by **Tony** » Fri Jan 30, 2015 6:18 pm

Hey Kev, that build is looking great, missed out a bit on the forum lately....Lee is posting my quad tomorrow, yippee

KevG · Post by **KevG** » Fri Jan 30, 2015 10:07 pm

Glad your getting it back mate,

KevG · Post by **KevG** » Fri Jan 30, 2015 10:28 pm

Well I got to play for a short time when I came home from work today before I had to go back out to pick up my daughter from school,

The outcome, found out my flight mode switch position zero was picking up flight mode 3 which was rate, rate, rate. So swapped it to attitude, attitude and axis lock, but I was getting oscillating so dropped the gains down but got to a point where I felt I was losing the locked in feel, and it felt like it wanted to move in an inconsistent patern,

So then came the strip down, why you may ask, well I hard mounted the cc3d, and it seemed like it was getting vibes, so took the hard mount posts off, and was going to soft mount it directly to the base plate but I did not want to put double sided on the pcb board, so I got some blister pack clear plastic, and put the posts on the board then screwed the plastic to them, that gave me a test bed for attaching the unit to try my theory before ordering a case from China, now the wait for the case, but Banggood is pretty good so should not be to long

This mod worked a treat after a quick test, need to raise the gains a bit again but she flys beautifully now, well when I say flys beautifully it hovers in my living room beautifully, lol

The maiden will come and will have video of some sort, even if it is from on board,

Lee · Post by **Lee** » Sat Jan 31, 2015 8:43 am

Nice Kev. Have fun.

KevG · Post by **KevG** » Sat Jan 31, 2015 8:59 am

Thanks mate,

Quick question though, how did you assign channel six in your tx,want to put it on the knob to tune pid

Graham Lawrie · Post by **Graham Lawrie** » Sat Jan 31, 2015 12:40 pm

More pics please:)

KevG · Post by **KevG** » Sat Jan 31, 2015 3:24 pm

Here you go graham, this will be torn down again to fit the hard case and the wire management

: image.jpg (1.59 MiB) Viewed 4606 times

: image.jpg (1.47 MiB) Viewed 4606 times

: image.jpg (1.65 MiB) Viewed 4606 times

Graham Lawrie · Post by **Graham Lawrie** » Sat Jan 31, 2015 4:05 pm

Very nice Kev. I only put lights on the tail:) I have flown it at a distance and it really helps with orientation:)

Marius · Post by **Marius** » Sat Jan 31, 2015 8:00 pm

Sweet!

KevG · Post by **KevG** » Tue Feb 03, 2015 12:56 pm

Another 2 Zippy compact 1500's ordered seeing as they had about a quid off each in HK sale, satisfied with that,

Derek · Post by **Derek** » Tue Feb 03, 2015 1:25 pm

That really is pretty cool, Kev! Very nice!

cml001 · Post by **cml001** » Tue Feb 03, 2015 1:39 pm

Awesome.. Love the lights!

KevG · Post by **KevG** » Tue Feb 03, 2015 1:53 pm

Thanks guys was a nice little build, but still a fair bit of tidying up to do, OCD strikes again I'm afraid,

Can't wait to get FPV gear now, want to try it so much, but have to be patient I'm afraid,

KevG · Post by **KevG** » Tue Feb 03, 2015 9:15 pm

Was not to fussed on the landing gear post type things this quad came with as well as the plastic screws break easy, but did not want it siting on the frame nuts,

So I had a brain fart and came up with these,

: image.jpg (811.25 KiB) Viewed 4576 times

It's made out of the high density packing that was around the motors in the boxes and just double sided on to the arms,

cml001 · Post by **cml001** » Tue Feb 03, 2015 11:41 pm

Ur a genius! At a glance I thought they were the little foam thingies used to route wires & fuel tubing.. Same shape as ur mod. Awesome job bruh!

Graham Lawrie · Post by **Graham Lawrie** » Wed Feb 04, 2015 8:12 pm

Nice one:)

KevG · Post by **KevG** » Thu Feb 05, 2015 10:57 am

Second two batteries arrived this mornings so guess I have more soldering to do lol, keep me flying though

KevG · Post by **KevG** » Sat Feb 07, 2015 12:18 pm

Well my daughter has had a freind over to play this morning so it gave me the ideal time to fiddle with the quad, so took the time to resolver and clean up my PDB.

The before photo shows how ragged it looked under the bottom frame,

: image.jpg (627.31 KiB) Viewed 4535 times

Then the after photo, and yes there is the same amount of wires there,

: image.jpg (697.97 KiB) Viewed 4535 times

After that photo I covered the board with insulation tape, just for a bit of protection.

And with the bottom frame on,

: image.jpg (786.24 KiB) Viewed 4535 times

And here you can see the finished quad, although I have to remove the cc3d again to put it in a case,

: image.jpg (808.38 KiB) Viewed 4535 times

Stambo · Post by **Stambo** » Sun Feb 08, 2015 9:33 pm

After seeing that I am almost embarrassed to show my wiring.
I go for functional not pretty.

RC-Hangout

Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread