Assault 700 experiences

Discussion, questions, builds and tutorials on 550 size helicopters on up.

Moderator: Moderators

Post Reply
User avatar
Kickedd7371
Member
Member
Posts: 153
Joined: Tue Aug 18, 2015 7:28 am
Location: Western Australia

Assault 700 experiences

Post by Kickedd7371 »

I thought I would share my setup/thoughts and experiences on the Assault 700 as requested by a forum member.

I order the kit at the start of the year and ended up getting it fully kitted out late April. The Setup are as follows:
690mm RotorStar Main Blades
RJX Carbon fiber tail blades 105mm
YEP 120A
Turnigy SK3 4962 500kv
Rotor Star Dual power 15A Voltage regulator
Turnigy 1259TG cyclic servos
Turnigy 1257TG tail servo
iKon
Spectrum Satellite receivers

The built itself from what i can remember went down smoothly without any hitches. The manual isn't that good to be honest but it is pretty easy to figure out where everything goes (This was my second heli and I managed to figure it out). The maiden flights went down without a hitch as well. So i have logged over 66 flights with the machine and I think I can formulate a reasonable opinion at this stage. The heli itself is great, the quality of the main frame, bearing blocks, main rotor head and tail are very nice. My tail boom came with a light dent in the side luckily it wasn't bent besides it isn't actually noticeable unless to try to find the indentation. The drive train or more specific the main gear is where this machine is slightly let down. The motor I run is perfect in terms of its power (Being a 3.5KW motor) for this main gear. I suspect that if you run a more powerful more than that the main gear is very likely to strip since it is running non slanted plastic gear. I had to replace my main gear 53 flights in because I cracked a gear tooth during high rate flips. Not a deal breaker since the replacement cost around $10 directly from the manufacturer (Gartt RC). If you want to use this machine with a more powerful motor I would recommend you get yourself the align slanted gear. Another plus this model has is the fact the 99% of the align parts fit directly on it without any modification. The swash plate on mine is from version 2 and it seems to be holding up well but then again I am not running extreme servos on the cyclic so with servos such as the bk8001 you may have issues. Again if you want this to be a hard 3D machine you will prob want to swap out the swash as well but that is the thing it is all depends on your flying style. If you intend to do sport flying and some mildish 3D then this is a great machine especially at the price point.

Here is some recent footage of me flying my Assault:
https://www.youtube.com/watch?v=JoTuJPYGa24
Attachments
11222538_1112666362082444_1184283680180094973_n (1).jpg
11222538_1112666362082444_1184283680180094973_n (1).jpg (135.35 KiB) Viewed 3558 times
User avatar
Graham Lawrie
Moderator
Moderator
Posts: 5049
Joined: Thu Nov 06, 2014 7:14 pm
Location: Kinlochleven, Scotland
Contact:

Re: Assault 700 experiences

Post by Graham Lawrie »

Nice one:) Love the Goblin 700:) Cameron on here has one:) Good to hear that the assault is a reasonable entry heli at this size for someone like me that cant fly 3D:)
Align 600
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius




CITIZEN # 521
User avatar
Derek
Supporter
Supporter
Posts: 3948
Joined: Fri Nov 07, 2014 7:45 pm
Location: Fort Wayne, Indiana, USA

Re: Assault 700 experiences

Post by Derek »

hey buddy...thanks a lot for that bit of write up!!! Like I mentioned in the other thread, I was given an Assault 700 frame and I was curious about your experiences. To my knowledge, mine is also the V2 so I am confident that I have the new swash and tail. Now, you say that you have logged 66+ flights on yours. That's very encouraging! It's even more encouraging considering the fact that you are obviously more skilled than I am so if the helicopter can handle your flying style, it should very well be able to handle mine. I'm more of a sport flyer with mild and occasional 3D.

Thanks for taking the time to post some info and I hope that you continue to share your flight videos of the Assault 700 as well as your other models.

Take care!!
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8

Citizen # 00744
User avatar
Kickedd7371
Member
Member
Posts: 153
Joined: Tue Aug 18, 2015 7:28 am
Location: Western Australia

Re: Assault 700 experiences

Post by Kickedd7371 »

Graham Lawrie wrote:Nice one:) Love the Goblin 700:) Cameron on here has one:) Good to hear that the assault is a reasonable entry heli at this size for someone like me that cant fly 3D:)
Thank you :) . Yeah it is definitely a reasonable entry heli for sure.
Derek wrote:hey buddy...thanks a lot for that bit of write up!!! Like I mentioned in the other thread, I was given an Assault 700 frame and I was curious about your experiences. To my knowledge, mine is also the V2 so I am confident that I have the new swash and tail. Now, you say that you have logged 66+ flights on yours. That's very encouraging! It's even more encouraging considering the fact that you are obviously more skilled than I am so if the helicopter can handle your flying style, it should very well be able to handle mine. I'm more of a sport flyer with mild and occasional 3D.

Thanks for taking the time to post some info and I hope that you continue to share your flight videos of the Assault 700 as well as your other models.

Take care!!
Your are welcome :) . The Assault has been a very good heli so far. It will treat you well as long as you treat it well. Again some tips for once you do get it up and running. These should be normal heli maintenance anyways but I always tend to drop some silicon oil on the main shaft, swash plate and the tail shaft to ensure everything runs nice and smoothly. Also be sure to check screws on regular basis and inspect the gear (I also use lubricant here). If you do these things I am fairly confident this machine can last you a long time.
User avatar
Tony
Supporter
Supporter
Posts: 3203
Joined: Thu Nov 06, 2014 3:01 pm
Location: United Kingdom

Re: Assault 700 experiences

Post by Tony »

Nice birds there mate, and awesome flying..
Tony - AKA Blackwarrior - nice to be home again
Novice pilot
HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
User avatar
cml001
Supporter
Supporter
Posts: 2882
Joined: Fri Nov 07, 2014 4:46 pm
Location: Augusta GA

Re: Assault 700 experiences

Post by cml001 »

Good flights!
Team Synergy / Rail Blades / Pro Tune
Pulse Battery
Castle Creations
Morgan Fuel
User avatar
Kickedd7371
Member
Member
Posts: 153
Joined: Tue Aug 18, 2015 7:28 am
Location: Western Australia

Re: Assault 700 experiences

Post by Kickedd7371 »

Tony wrote:Nice birds there mate, and awesome flying..
Thank you! :)
cml001 wrote:Good flights!
Cheers ! :)
User avatar
Kickedd7371
Member
Member
Posts: 153
Joined: Tue Aug 18, 2015 7:28 am
Location: Western Australia

Re: Assault 700 experiences

Post by Kickedd7371 »

Well I decided to add some lights on the Assault and turn it into my night flying heli. So far, I have had two successful night flights that encompassed basic circuit flying and inverted hovering. I have some flight video but can't really see much so here are some photos I took of it with my gopro while it was on the ground (see attachments)
Attachments
IMG_0369.JPG
IMG_0369.JPG (3.06 MiB) Viewed 3443 times
IMG_0368.JPG
IMG_0368.JPG (3.49 MiB) Viewed 3443 times
User avatar
Derek
Supporter
Supporter
Posts: 3948
Joined: Fri Nov 07, 2014 7:45 pm
Location: Fort Wayne, Indiana, USA

Re: Assault 700 experiences

Post by Derek »

That's too cool, buddy! I hope you can share some flight video.
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8

Citizen # 00744
User avatar
Kickedd7371
Member
Member
Posts: 153
Joined: Tue Aug 18, 2015 7:28 am
Location: Western Australia

Re: Assault 700 experiences

Post by Kickedd7371 »

Derek wrote:That's too cool, buddy! I hope you can share some flight video.
Flew again tonight and had my dad record it. I shall upload and post that as soon as I can :) You won't see too much except the light glow around the heli but still looks kinda cool :P
User avatar
Graham Lawrie
Moderator
Moderator
Posts: 5049
Joined: Thu Nov 06, 2014 7:14 pm
Location: Kinlochleven, Scotland
Contact:

Re: Assault 700 experiences

Post by Graham Lawrie »

Very cool:)+1 on Derek, video would be great to see:)
Align 600
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius




CITIZEN # 521
User avatar
Kickedd7371
Member
Member
Posts: 153
Joined: Tue Aug 18, 2015 7:28 am
Location: Western Australia

Re: Assault 700 experiences

Post by Kickedd7371 »

Uploaded the video and can be found in my flight log:
http://www.rc-hangout.com/forum/viewtop ... 421#p20421
User avatar
Kickedd7371
Member
Member
Posts: 153
Joined: Tue Aug 18, 2015 7:28 am
Location: Western Australia

Re: Assault 700 experiences

Post by Kickedd7371 »

Well after stripping my main gear twice i decided to throw in an align slanted gear. I only had one flight with the new gear so far and wow I like this gear a lot. The heli is so much quieter than before. I also chucked on some black landing gear because why not haha.
Attachments
IMG_0499.JPG
IMG_0499.JPG (3.76 MiB) Viewed 3387 times
IMG_0503.JPG
IMG_0503.JPG (2.74 MiB) Viewed 3387 times
Post Reply

Return to “Big Helis (550+)”