SUPER BAD'S OXY3

Post by **pvolcko** » Thu May 21, 2015 2:11 pm

Cool. I have the microikon in a box here, awaiting installation on the 180CFX. Just not enough time lately. Need to start doing all this stuff at night while I watch some TV.

Superbad · Post by **Superbad** » Sat May 23, 2015 12:27 am

Well Dose the size matter

Post by **pvolcko** » Sat May 23, 2015 5:52 am

Gotta be a pain to rewire all those leads to micro-jst connectors.

cml001 · Post by **cml001** » Sat May 23, 2015 11:23 am

It's soo cute!

Superbad · Post by **Superbad** » Mon May 25, 2015 11:51 pm

Got it put in and wired up

Derek · Post by **Derek** » Tue May 26, 2015 12:30 am

That's cool, Jesse! You can barely see that it's there

Superbad · Post by **Superbad** » Tue May 26, 2015 12:54 am

Ya the full size Ikon stuck out like a sore thumb . It took up the whole tray there were the micro Ikon is

Post by **pvolcko** » Tue May 26, 2015 1:16 am

Nice, can't wait to hear your report on flight.

Superbad · Post by **Superbad** » Tue May 26, 2015 1:26 am

Well the set up wasnt bad
I just saved the file from the Ikon and loaded it in the micro Ikon
Then went over it to recheck it All looks good
NOW if it will stop freaken RAINING

Graham Lawrie · Post by **Graham Lawrie** » Thu May 28, 2015 10:55 am

Nice one Jesse:) looks a neat and tidy installation:)

Superbad · Post by **Superbad** » Thu May 28, 2015 6:36 pm

Thanks Graham
Its hard to hide all the wires on this little sucker

Superbad · Post by **Superbad** » Sat May 30, 2015 12:01 am

Got a break in the rain and got to put the Oxy 3 with Micro Ikon in the air .
Didn't Take much and its back to flying like it was
So the Micro Ikon is a go for a 450 or smaller bird
you can get the adapters for full size servo plugs and be done or do like I did and cut and solder the JST leads to the servo wires to clean it up some

cml001 · Post by **cml001** » Sat May 30, 2015 1:19 am

Kool!

Lee · Post by **Lee** » Sat May 30, 2015 7:17 am

Looks great Jesse. That micro Ikon is sweet

Post by **danhampson** » Sat May 30, 2015 7:22 pm

the ikon i have has never missed a beat, nice to hear the micro is the same.

Superbad · Post by **Superbad** » Sat May 30, 2015 8:40 pm

Thanks Lee .
Looks a lot better than the big red brick hang out back there LOL

And Dan
It dose seem to be just like its big brother in the way it flys . If it will ever stop raining Ill get out and do some flying
Got to tune the Ikon on the 550 now

RC-Hangout

SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3

Re: SUPER BAD'S OXY3