Here is my latest mini.
It's going to be 4s, but while I'm waiting for the batteries, I stuck a set of 6040 dal props on it.
These will be cut down to 5040 bullnose, once the 4s arrive.
image.jpg (1.81 MiB) Viewed 3589 times
image.jpg (1.85 MiB) Viewed 3589 times
image.jpg (1.82 MiB) Viewed 3589 times
GOBLIN 570------IKON WARP 360--------IKON QAV 500----------Open Pilot RCXH250---------Open Pilot
RCX 250 Minquad FPV addiction
500 X quad FPV/AP platform
450 X quad set up for night flight
Multiple WLToys V911, V949, V959
Taranis, Turnigy 9X
Fatshark Predator, Immersion 5800 Duo
Trex 500 Esky Belt CP V2
Here you go Graham.
I did have one issue with the PDB. The 12V out wouldn't let me run my FPV gear.
Couldn't get a picture.
Plugged it straight into a battery, and worked perfectly.
So i tried the pins ment for LEDs and it worked perfectly too. So I left them there.
Means I can switch my FPV gear on and off if i want
IMG_0026.jpg (2.88 MiB) Viewed 3578 times
You can buy the PDB from banggood or myrcmart for about $10.
It has solder points for the Nase and the CC3D to directly mount to the board.
GOBLIN 570------IKON WARP 360--------IKON QAV 500----------Open Pilot RCXH250---------Open Pilot
Tony - AKA Blackwarrior - nice to be home again
Novice pilot HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
Lee wrote:Here you go Graham.
I did have one issue with the PDB. The 12V out wouldn't let me run my FPV gear.
Couldn't get a picture.
Plugged it straight into a battery, and worked perfectly.
So i tried the pins ment for LEDs and it worked perfectly too. So I left them there.
Means I can switch my FPV gear on and off if i want :
IMG_0026.jpg
You can buy the PDB from banggood or myrcmart for about $10.
It has solder points for the Nase and the CC3D to directly mount to the board.
@Lee/Tony What are the parts marked XK?
Mine arrived with the surround chipped, i have complained and ordered new ones, but wondering if i can use them if i hot glue them:)
Lee wrote:Here you go Graham.
I did have one issue with the PDB. The 12V out wouldn't let me run my FPV gear.
Couldn't get a picture.
Plugged it straight into a battery, and worked perfectly.
So i tried the pins ment for LEDs and it worked perfectly too. So I left them there.
Means I can switch my FPV gear on and off if i want
IMG_0026.jpg
You can buy the PDB from banggood or myrcmart for about $10.
It has solder points for the Nase and the CC3D to directly mount to the board.
A few people have said the 12v is week for the vtx and cam normally if using a 12v cam, i have mine running from the 12v out to the vtx then that powers the cam at 5v and I have had not an issue,
Minor league Aviator, against gravity which normally wins!
RotoriousFPV quads Micro Rad 3" Gat 4" and Rad 5"
D-Quad Obsession
Yuneec Typhoon H
Taranis Qx7,
"A few people have said the 12v is week for the vtx and cam normally if using a 12v cam, i have mine running from the 12v out to the vtx then that powers the cam at 5v and I have had not an issue,"
Not sure what the XK is. MR Electronics man will tell you, I'm sure
Mine is working perfectly since moving the VTX to the LED pins and not the 12V out pins.
GOBLIN 570------IKON WARP 360--------IKON QAV 500----------Open Pilot RCXH250---------Open Pilot
