Motor problem spining

[DOG]

Hey there. I just had a strange problem occur. When I plug my Naze32 Rev6 into clean flight, everything works like it suppose to. All 4 motors spins in clean flight and with the TX turn on too. When I disconnect from clean flight and try to power up the quad with the TX, only one motor will spin. This was working fine before and now all of the sudden it doesn't. Can anyone tell me what might of went wrong?

[Graham Lawrie]

Check that you have the correct settings in rx eg TAER etc

[Derek]

This sounds like a similar problem that im having with the Naze32 rev6 that is on my Dads 450 quad. Absolute PITA!

[DOG]

Hey Derek. It the same FC and the same problem. Where can I find another Naze32 Rev6?

[Derek]

Honestly, id venture away from the Naze32 rev6. I love the rev5 because it just works but i read that support for the rev5 is going to be eliminated soon. I guess its about time to jump on the "f4 band wagon."

[DOG]

Sounds good. It makes two of us

[KevG]

Honestly, id venture away from the Naze32 rev6. I love the rev5 because it just works but i read that support for the rev5 is going to be eliminated soon. I guess its about time to jump on the "f4 band wagon."

There is no support for the Naze rev5 any longer in Betaflight as its not got the power to handle it anymore, cant run the loop and gyro rates with the poor processor

[Derek]

lol, yeah...I just watched a short video by Painless360. He was talking about that. I guess I need to start hoping that my Naze32 (on ZMR250 and Gravity250) continue to work.

[Stambo]

I still run the Naze32 on my quads, and as long as they continue to do what they are at the moment there is no need to upgrade firmware.
I will however, probably switch the Blackout 360 to Omnibus F4 and Inav for the GPS features.

[Graham Lawrie]

Most of mine are Rev 5:)

[DOG]

Hey all, I'm getting a new Flight controller for my fossil 210 and I was wondering what is the difference between theses two FC beside built in OSD barometer https://www.gearbest.com/flight-control ... 90559.html and https://www.gearbest.com/flight-control ... 25824.html I'm planning to get 2. 1 for back up or should I get one of each

[KevG]

id advise against the omnibus, and say I love my Matek f405 osd.

[Stambo]

id advise against the omnibus, and say I love my Matek f405 osd.

Any particular reason?
Don't have a problem with mine, I have the V2, so far it's great.

V2 has a current sensor, OSD on these things is great in my Nano Talon.

[DOG]

Hey there. Fossil recommends seriously pro FC for my 210. Now I'm getting confuse lol. I'm no way near you guys flying level but I would like to find a nice working FC. with the Omnibus V3, matek F405 osd or the seriously pro. What do you think about this one for a beginner like me https://www.helidirect.com/fpv/electron ... d-vtx.html

[KevG]

id not recommend the seriously pro stuff as there has been to many problems with them,

forget your a beginner the fc knows nothing of that, me myself for a fsgx I would go for a betaflight f4 osd, you wont then need a pdb as its built in and you can solder the esc's direct on. lots of videos and group chats for info on it as well. I have used the f3 version all year and its been a great fc,

or use a furious fpv kombini like I did in my fsgx another great fc but with no osd.

20160916_185151[1].jpg (1.56 MiB) Viewed 3919 times

20160917_220527[1].jpg (1.29 MiB) Viewed 3919 times

[DOG]

Thanks KevG for that information. I'll look into that.