SYNERY N5C TT.. IT BEGINS!

cml001 · Post by **cml001** » Tue Jan 13, 2015 1:33 am

http://youtu.be/-bzWSJG93P8

Superbad · Post by **Superbad** » Tue Jan 13, 2015 1:40 am

YA AND

cml001 · Post by **cml001** » Tue Jan 13, 2015 2:12 am

Behold! The Synergy N5C TT Edition.

cml001 · Post by **cml001** » Tue Jan 13, 2015 2:33 am

So.. This will be my first dive into nitro... And after inspecting the box contents, I think I picked a good one.. Lots & lots of aluminum... Love that.. Ill be using the O.S. 55 HZ-R with a Hatori SAB-55 muffler... PushGlo igniter... I picked up an Align starter a couple weeks ago second hand...MKS servos all the way round.. HBL960 cyclic(still waiting on 2 of them as ExpienceRC only had 1 in stock), HBL990 tail, and a HV9780 mini tail for the throttle. iKon FBL w Cirus bluetooth module.. 2 DSMX sats.. 3600mah 2S Pulse to a heavy duty Futaba switch to power the electronics.. Rail 606 mains & 106 tail blades... Think I'm gonna do the plumbing & sheathing in green & accent the hardware blue... Gotta have that color. Gonna take my time on this build.. As stated I've never done nitro before so.. Plus I'm still waiting on ExpierienceRC to get more HBL960s in so I can start this.. May go ahead & get the sub assemblys done.. Anyhow ill try to take pics along the way and do a better documentation than I did on the Align 550.

Superbad · Post by **Superbad** » Tue Jan 13, 2015 2:51 am

Thats A NICE Kit

Post by **pvolcko** » Tue Jan 13, 2015 4:17 am

Awesome buy, Clay. Looking forward to this build thread and flight vids!

murankar · Post by **murankar** » Tue Jan 13, 2015 5:39 am

Nice one clay. Have fun and take your time. Lots of new stuff for ya.

Post by **danhampson** » Tue Jan 13, 2015 7:36 am

Very nice Clay look forward to this build. I've fancied a synergy for over 12 months.
good luck with the nitro part I will be keeping a close eye on this thread.

cml001 · Post by **cml001** » Tue Jan 13, 2015 7:45 am

Ok... The excitement has got the better of me.. Along with about half a pot of coffee.. Didn't realise it was 230AM... Here are a couple shots of the nights work. First off were the skids. Synergy does it different than Ive seen others.. No set screw.. The small threaded cylinders go inside the pipes, then the pipes inside the skid, then a screw thru the skid & pipe into the cylinder.. Takes a little work to line them up.

cml001 · Post by **cml001** » Tue Jan 13, 2015 7:55 am

I knew there was gonna be some epoxy work on the CF pushrod ends.. So I decided to do that tonight so it could cure all night. The boom supports require the same.. But opt'd for KDE boom supports.. They are beefier than Align supports and I've been using them on both my 450 & 550... But these Synergy ones are pretty big in diameter... Already got the KDE.. I also did the TT so it could cure as well.. Did green 260 loctite on the TT bearings.. Always just used CA before.. Thought I'd try this.. I'll post finished shots after they cure tomorrow.. Here is the before.

cml001 · Post by **cml001** » Tue Jan 13, 2015 8:01 am

Next I did the tail box & rotor. It's freak'n huge compared to the Align 550.. I did replace the plastic ringed pitch slider that came with this kit for the newer version that comes with the N7 & the E7SE. I also pulled the bearings outta the plastic crank and put them in the aluminum one I got from FBL Rotors.

KevG · Post by **KevG** » Tue Jan 13, 2015 8:06 am

Sweet Clay nice bird, will be following this one,

cml001 · Post by **cml001** » Tue Jan 13, 2015 8:07 am

Little trick I do on hubs and spindles.. Cut the tips of a Q-Tip off (use a tooth pick on 450's) and dip one end in alcohol and thread it into the ends and the the dry side.. Cleans up the oils in them.. Then do it again with a clean dry one and leave it in... Assemble & grease ur bearings and put them in the grip.. Then put it on the hub and take out the swab piece... This keeps the newly greased bearing from contaminating the threads.

cml001 · Post by **cml001** » Tue Jan 13, 2015 8:13 am

Little trick I do on hubs and spindles.. Cut the tips of a Q-Tip off (use a tooth pick on 450's) and dip one end in alcohol and thread it into the ends and then the dry side.. Cleans up the oils in them.. Then do it again with a clean dry one and leave it in... Assemble & grease ur bearings and put them in the grip.. Then put it on the hub and take out the swab piece... This keeps the newly greased bearing from contaminating the threads.

murankar · Post by **murankar** » Tue Jan 13, 2015 8:40 am

I use green thread locker on my torque tube bearings and ends also. Works great, so great they won't come apart. Looks really nice and shiny.

Tony · Post by **Tony** » Tue Jan 13, 2015 10:37 am

Ok Clay, I'm lost with that first Star Wars vid....haha, what was all that about?

The new kit looks awesome, looking forward to seeing this build.. Nice one

Graham Lawrie · Post by **Graham Lawrie** » Tue Jan 13, 2015 11:41 am

Nice one Clay:) good to see you did not get caught up in the addiction of a build and work past your deadline:) LOL

Nice gear you have there:) well done young Jedi:) May the 4th be with you:)

Graham Lawrie · Post by **Graham Lawrie** » Tue Jan 13, 2015 11:42 am

Need to take Tony away from the dark side

eh Tony:) LOL

cml001 · Post by **cml001** » Tue Jan 13, 2015 12:57 pm

Tony, not so much a video, but the music... Click on it again.. Sit back & close ur eyes... Then open ur eyes while looking at the Synergy... Yeeaaahhh! Lol.. Very shiny.. & huge.. Look at it compared to the 550's box.

cml001 · Post by **cml001** » Tue Jan 13, 2015 12:58 pm

Actually the pic doesn't do justice as I'm holding the new tail box further away from the lens...

RC-Hangout

SYNERY N5C TT.. IT BEGINS!

SYNERY N5C TT.. IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!

Re: IT BEGINS!