RCX250 3K Carbon (DT Version)

Lee · Post by **Lee** » Wed Jan 28, 2015 11:42 pm

Mine are to the rear. USB port on the left hand side. Yaw -90
Check on the flight data menu with the HUD to see if its right.

Graham Lawrie · Post by **Graham Lawrie** » Sat Jan 31, 2015 1:36 pm

Quick question Lee:) How are you attaching the rubber band for the Mobius?

Lee · Post by **Lee** » Sat Jan 31, 2015 6:07 pm

Its just looped over the plate between the rubber mounts. The plate has velcro on it. And incase there is a crash, and the plate comes off, theres a loose zip tie to keep things together.

Graham Lawrie · Post by **Graham Lawrie** » Sat Jan 31, 2015 7:15 pm

I hvae got the cable tie the same:) What i was thinking was that you had it connected to the frame?

Lee · Post by **Lee** » Fri Feb 13, 2015 8:47 pm

Been doing some mods to my frame.
Cut up an old nylon cutting board ( don't tell Celia) LOL

This will give some vibration insulation, and make room between the two bottom frames.
Going to put as much stuff between those frames, but not the ESCs. They are to big.

: 100_3552.JPG (387.16 KiB) Viewed 2364 times

: 100_3553.JPG (401.37 KiB) Viewed 2364 times

: 100_3554.JPG (336.04 KiB) Viewed 2364 times

: 100_3555.JPG (336.5 KiB) Viewed 2364 times

cml001 · Post by **cml001** » Fri Feb 13, 2015 10:08 pm

Now is that layer additional or part of the kit?.. Never mind.. I see it.

Derek · Post by **Derek** » Fri Feb 13, 2015 10:27 pm

That's cool! It looks like it was meant to be there!

Tony · Post by **Tony** » Fri Feb 13, 2015 11:41 pm

Looks cool Lee, nice colour too

Graham Lawrie · Post by **Graham Lawrie** » Sat Feb 14, 2015 9:45 am

Good idea:)

Lee · Post by **Lee** » Wed Mar 04, 2015 7:51 pm

Finished the rebuild of the RCX250.

Longer screws, makes the frame stiffer, and the heads are a larger key, so less chance to strip.

: Much longer, stiffer frame.; 100_3579.JPG (362.94 KiB) Viewed 2341 times

: New screws on the left; 100_3576.JPG (374.21 KiB) Viewed 2341 times

: 100_3580.JPG (278.31 KiB) Viewed 2341 times

Cabling go through slots in the new damper pads

: 100_3585.JPG (380.64 KiB) Viewed 2341 times

Had these green vibe mounts lying around, so thought i'd use them on the board.

: 100_3586.JPG (392.28 KiB) Viewed 2341 times

Ready for action

: 100_3590.JPG (335.47 KiB) Viewed 2341 times

Graham Lawrie · Post by **Graham Lawrie** » Wed Mar 04, 2015 7:55 pm

Quite neat Lee:)

Tony · Post by **Tony** » Wed Mar 04, 2015 11:24 pm

i see the battery on the top now Lee.... isnt the bottom better?

Lee · Post by **Lee** » Thu Mar 05, 2015 12:02 am

With the bigger screw heads, it wasn't possible underneath Tony.

Lee · Post by **Lee** » Thu Mar 05, 2015 12:11 am

Put the legs back on. And the Dust cover.

: 100_3591.JPG (365.26 KiB) Viewed 2331 times

Tony · Post by **Tony** » Thu Mar 05, 2015 10:00 am

Looks pretty awesome like....can you get the angled motor arms for these 250's ?

ChrisFredriksson · Post by **ChrisFredriksson** » Thu Mar 05, 2015 11:39 am

Looks really awesome! I like the dust cover also, I was just thinking on the previous image above the dust cover photo, it's such a mess (not that it's worse than anyone else) but it's also kind of cool to see all the wires.. Then I though, I wonder if it would be possible to cover it up somehow, and yeah.. there you've done it

haha

RC-Hangout

RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)

Re: RCX250 3K Carbon (DT Version)