Emax nighthawk 250 build thread

KevG · Post by **KevG** » Sun Feb 08, 2015 10:15 pm

Yes but for me it's like cyptonite having raged wiring,

Just waiting for my cc3d case now, to get that closed in and mounted better

Graham Lawrie · Post by **Graham Lawrie** » Mon Feb 09, 2015 10:07 pm

Wait till you add FPV Kev:) mine was tidy till then:( had to try and tidy it up tonight , the mess of FPV wires is mad got it a bit tidier but still work to do on a shorter mini-pin harness for the TX to camera:(

KevG · Post by **KevG** » Sat Feb 14, 2015 7:16 pm

Well just ordered the naze32 to give that a try, will be going with clean flight on it as well,

Graham Lawrie · Post by **Graham Lawrie** » Sat Feb 14, 2015 10:05 pm

Be interesting to see what settings you have Kev. I have Baseflight, which is very similar to Cleanflight:)

Lee · Post by **Lee** » Sat Feb 14, 2015 10:29 pm

Just waiting for some 90º header pins to set my Flip32 up. Already got Cleanflight FW on it.

Post by **danhampson** » Sat Feb 14, 2015 10:42 pm

The PIDs on baseflight and cleanflight are the same as long as your pid controller is set to 0 in the pid tuning tab. Heres the link to cleanflight doc on migration: https://github.com/cleanflight/cleanfli ... eflight.md

KevG · Post by **KevG** » Sat Feb 14, 2015 10:47 pm

Yeah will be looking at all this next week mith my mate, down the hall,

KevG · Post by **KevG** » Mon Feb 16, 2015 11:41 am

Oh the irony, I have the case for the CC3d turn up the day before the new controller is supposed to,

: image.jpg (1.37 MiB) Viewed 3684 times

Tony · Post by **Tony** » Mon Feb 16, 2015 12:37 pm

Nice job on the wiring Kev. Sod's law about the case arriving when your going to change the controller...

KevG · Post by **KevG** » Mon Feb 16, 2015 12:55 pm

Yes mate, gonna put the controller in the case, and put it aside until I find out if I like this naze32, but looking at my mates bird its looking good at the moment,

Just got to solder it all up when it gets here, oh the joy,

Lee · Post by **Lee** » Mon Feb 16, 2015 4:22 pm

Same case as i have Kev.

KevG · Post by **KevG** » Mon Feb 16, 2015 4:27 pm

Banggood butt,

Going with this naze32 and I thought I would be doing cleanflight on it but the guys down here have baseflight so gong with that first to see what it's like then will prob cut over later when I have a bit more experiance, been looking through loads of shit on the Internet today trying to make my mind up,

Stambo · Post by **Stambo** » Mon Feb 16, 2015 6:22 pm

KevG wrote:Banggood butt,

Going with this naze32 and I thought I would be doing cleanflight on it but the guys down here have baseflight so gong with that first to see what it's like then will prob cut over later when I have a bit more experiance, been looking through loads of shit on the Internet today trying to make my mind up,

Good idea, if nobody around you has Cleanflight it will be better to use what they can help you with.
There is a learning curve with both, switching was quite easy once I understood baseflight.

Derek · Post by **Derek** » Mon Feb 16, 2015 8:15 pm

I actually thought the wiring job was pretty good! You should see the mess of wires on my 600, lmao.

KevG · Post by **KevG** » Mon Feb 16, 2015 9:39 pm

Well a little fiddling tonight,

Fitted the Cc3d case as I wanted the standoffs that was on the cc3d

: image.jpg (792.66 KiB) Viewed 3666 times

The new base plate for the naze32 unit which is what I wanted to rob the standoffs for,

: image.jpg (822.41 KiB) Viewed 3666 times

And a little side project, the transport case, I like a bit of protection for things while I carry them and found a case for a fiver, 8 bucks for our US friends, a few cable tidies and some elastics later and here is what we have,

: image.jpg (607.13 KiB) Viewed 3666 times

Now I'm all ready for the new controller, I think, see what board pins come with the naze32 tomorrow

Graham Lawrie · Post by **Graham Lawrie** » Mon Feb 16, 2015 9:55 pm

Nice one Kev:)

KevG · Post by **KevG** » Mon Feb 16, 2015 9:58 pm

Hey Graham do you want a couple of packs of Lynx trex 150 motor connectors, bought them for my quad lighting but did not use, they are yours if you want them,

Graham Lawrie · Post by **Graham Lawrie** » Mon Feb 16, 2015 10:21 pm

That would be cool Kev:)

Tony · Post by **Tony** » Tue Feb 17, 2015 12:01 am

Nice job Kev, love that case idea..

Lee · Post by **Lee** » Tue Feb 17, 2015 9:58 am

Nice case Kev

RC-Hangout

Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread

Re: Emax nighthawk 250 build thread