HELP on wood hull finish
Moderator: Moderators
Re: HELP on wood hull finish
With our weather currently being little more than cool and damp, it is not conducive to the drying of paint. Luckily, the older I have gotten the more patience I have developed.
Some preliminary info on this boat is...
It is 26 inches long, 10.5 inches at the widest and 4" deep(bottom of hull to top of rear hatch)
The gas powered version I based this on is to weigh 3 pounds 7 ounces. Mine weighs 3 pounds 11 ounces fully loaded with batteries and action figure though I still have a bit of painting yet to complete. I think it feels heavier because it is so short and wide.
It has a three blade Thunder Tiger D40 x P41 Neptune prop(I just liked the way it looked and it was the correct outer diameter) driven by a S2858-2630 Brushless Inrunner (2630kv) and using a Brushless Car ESC 60A w/ Reverse...we tried a water cooled ESC for boats but could not get it to act correctly so this was just simpler.
The receiver is a OrangeRx R615X DSM2/DSMX Compatible 6Ch 2.4GHz Receiver w/CPPM which works fine with the FS-GT3B transmitters I already am familiar with that I use on my converted ATVs.
Obviously it is just simple servo control for the rudder that I just hunted around for an after market unit of "near" the recommended size from the plans that was listed as "Water Rudder Kit for Model Airplane Floats" at HobbyKing.
The seat and steering wheel I stole off a Max Steel toy go cart. The seat slides back and forth for fitting the figure.
The intention is to run the whole thing off 12 volt rechargeables. I am curious what my run time will be.
Between this boat and my BOMBER I am WAY past ready to hit the parks. I have a 1/6th scale hovercraft in the works as well that I need to get moving on. Wish me luck...and Derek's help on the electronics.
On a personal note...as far as a name??? In my near 62 years I have found my name to be unique and do not use it much online. I have REALLY liked seeing "D's Dad" in these posts so if there is no objection...that suit's me. I am VERY proud of Derek.
Some preliminary info on this boat is...
It is 26 inches long, 10.5 inches at the widest and 4" deep(bottom of hull to top of rear hatch)
The gas powered version I based this on is to weigh 3 pounds 7 ounces. Mine weighs 3 pounds 11 ounces fully loaded with batteries and action figure though I still have a bit of painting yet to complete. I think it feels heavier because it is so short and wide.
It has a three blade Thunder Tiger D40 x P41 Neptune prop(I just liked the way it looked and it was the correct outer diameter) driven by a S2858-2630 Brushless Inrunner (2630kv) and using a Brushless Car ESC 60A w/ Reverse...we tried a water cooled ESC for boats but could not get it to act correctly so this was just simpler.
The receiver is a OrangeRx R615X DSM2/DSMX Compatible 6Ch 2.4GHz Receiver w/CPPM which works fine with the FS-GT3B transmitters I already am familiar with that I use on my converted ATVs.
Obviously it is just simple servo control for the rudder that I just hunted around for an after market unit of "near" the recommended size from the plans that was listed as "Water Rudder Kit for Model Airplane Floats" at HobbyKing.
The seat and steering wheel I stole off a Max Steel toy go cart. The seat slides back and forth for fitting the figure.
The intention is to run the whole thing off 12 volt rechargeables. I am curious what my run time will be.
Between this boat and my BOMBER I am WAY past ready to hit the parks. I have a 1/6th scale hovercraft in the works as well that I need to get moving on. Wish me luck...and Derek's help on the electronics.
On a personal note...as far as a name??? In my near 62 years I have found my name to be unique and do not use it much online. I have REALLY liked seeing "D's Dad" in these posts so if there is no objection...that suit's me. I am VERY proud of Derek.
Re: HELP on wood hull finish
Sorry for writing a BOOK in the previous post.
D's Dad
D's Dad
Re: HELP on wood hull finish
Hey Dad....I think you better recheck the receiver info on your boat. The OrangeRx receiver is what is in your plane. The receiver that you have in your boat is the 3 channel Frysky receiver that matches your trigger transmitter.
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Re: HELP on wood hull finish
What can I say? Derek is right...and always has my back. Had I actually read what I cut and pasted even I would have known I was wrong. The rest "should" be correct. I just added the second and last coat of paint to the bottom so I cannot physically see the interior. Unfortunately I was going by invoices and dates...and goofed. Lastly, I hope to have the top painted blue Saturday afternoon...then more pictures...and then the WATER. Again, can't wait.
Re: HELP on wood hull finish
gonna be awesome to see it run
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Re: HELP on wood hull finish
Lol... His user name is West!
Team Synergy / Rail Blades / Pro Tune
Pulse Battery
Castle Creations
Morgan Fuel
Pulse Battery
Castle Creations
Morgan Fuel
Re: HELP on wood hull finish
lol, good enough!
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Re: HELP on wood hull finish
Posted my last via page one of this thread(didn't see the last few post prior)... Sorry.. D's Dad it is! Can't wait to see her zing'n across the water!
Team Synergy / Rail Blades / Pro Tune
Pulse Battery
Castle Creations
Morgan Fuel
Pulse Battery
Castle Creations
Morgan Fuel
- danhampson
- Site Admin
- Posts: 1746
- Joined: Thu Nov 06, 2014 2:54 pm
- Location: Manchester, United Kingdom
- Contact:
Re: HELP on wood hull finish
It's a fantastic looking craft can't wait to see it in action.
FPV addict.
- Graham Lawrie
- Moderator
- Posts: 5049
- Joined: Thu Nov 06, 2014 7:14 pm
- Location: Kinlochleven, Scotland
- Contact:
Re: HELP on wood hull finish
Cool. Be great to see the video
Align 600
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius
CITIZEN # 521
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius
CITIZEN # 521
Re: HELP on wood hull finish
You can be sure that my Dad will get video, Graham. No worries there. He's quite proud of the boat that he's built.
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Re: HELP on wood hull finish
No need to apologies about the book D's Dad, it's all valueable information, and if there's one thing this lot love, it's information on a craft.... Looking forward to seeing it thrashing the waves....
Tony - AKA Blackwarrior - nice to be home again
Novice pilot
HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
Novice pilot
HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
Re: HELP on wood hull finish
My Dad is more of a "scale" rc'er. I do believe his plans are to simply get the boat to move at a "scale" speed. Will he ever take it "wide open-full throttle"? I rather doubt it, lol. Nonetheless, it will be cool to see his scratch build project come to life.
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Re: HELP on wood hull finish
No surprise here. The paint dried enough I could turn the boat back over to look inside. The receiver is a Fly-Sky FS-6R3F three channel. I expect I will be masking off the hull tomorrow and painting the top. My main focus today is to finalize the magnetic front hatch so I can get it sealed and eventually painted as well. For now here's a few shots with the bottom done. Looks like I got a pretty good shine to the finish.
As Derek mentioned, my "WOW" factor is when you see a video or picture of one of my efforts and are not sure if it is scale or full size.
D's Dad
As Derek mentioned, my "WOW" factor is when you see a video or picture of one of my efforts and are not sure if it is scale or full size.
D's Dad
Re: HELP on wood hull finish
That really looks great, Dad! Nice job!!!
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Re: HELP on wood hull finish
That's looking awesome... Nice one
Tony - AKA Blackwarrior - nice to be home again
Novice pilot
HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
Novice pilot
HK450 FBL - Hubsan X4 - RCX H250 FPV Quad with Skyzone goggles..
I reserve the right to be wrong: if proved wrong: I reserve the right to change my mind!!
Re: HELP on wood hull finish
Fantastic!
Team Synergy / Rail Blades / Pro Tune
Pulse Battery
Castle Creations
Morgan Fuel
Pulse Battery
Castle Creations
Morgan Fuel
Re: HELP on wood hull finish
Just an update with, most likely, TOO many pictures but here goes. Basically...the boat is done. I just need to get some Velcro to secure the ESC and the receiver.
This should show the prop and rudder rather well
The cockpit is flat black and the bucket seat is on a track to slide forward and back. And it has a seat belt. Safety first.
I was trying to come up with a way to hide the rare earth magnets holding the front hatch on, as I did not allow for this in the design, when I came across these "buttons". They are metal and thick enough I was able to hold them in my lathe and turn out the backside to hold the magnets. As they are brass(plated) and the prop is brass I thought it would look OK. Looks OK to me.
Crowded in the aft...
...not so crowded in the engine compartment. I hope this is of interest and the next time you see it...there will be water around it.
This should show the prop and rudder rather well
The cockpit is flat black and the bucket seat is on a track to slide forward and back. And it has a seat belt. Safety first.
I was trying to come up with a way to hide the rare earth magnets holding the front hatch on, as I did not allow for this in the design, when I came across these "buttons". They are metal and thick enough I was able to hold them in my lathe and turn out the backside to hold the magnets. As they are brass(plated) and the prop is brass I thought it would look OK. Looks OK to me.
Crowded in the aft...
...not so crowded in the engine compartment. I hope this is of interest and the next time you see it...there will be water around it.
- Graham Lawrie
- Moderator
- Posts: 5049
- Joined: Thu Nov 06, 2014 7:14 pm
- Location: Kinlochleven, Scotland
- Contact:
Re: HELP on wood hull finish
Very nice:) apart from the bimbo:) LOL
Align 600
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius
CITIZEN # 521
Align 550
Align 450 Pro V2 AR7200BX
Align150
Mini-Quad 250/Emax NightHawk /Fossil V2/TBS Disco/Volt
DX6i
MHS Brain/Spartan Vortex/AR7200BX /Microbeast Plus HD
Blade mqx
Scorpion BUG
Fatshark Predator V2 & Mobius
CITIZEN # 521
Re: HELP on wood hull finish
lol...that's funny!Graham Lawrie wrote:Very nice:) apart from the bimbo:) LOL
Dad...that boat really turned out great! We'll get the esc and receiver secured and then it's time for the water. Have you done any buoyancy tests yet?
Derek
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744
Foam Board Scratch Build Plane Fanatic
HK Assault 700 (to be built)
Align Trex 600 Pro DFC, Ikon
Align Trex 500e
ZMR 250 FPV Race Quad
HK Skyfun with 5.8ghz FPV
Spektrum DX8
Citizen # 00744